To avoid a heavy power drain when the cold amplifier is first switched on, we conceived a "Soft-Start" mode which also functions as an "Ever-Warm" position allowing the amplifiers to be always warmed up for pleasurable listening. Each amplifier only consumes 30 watts of power in Ever-Warm mode. A blinking green LED reminds the user that the amplifier is in warm-up mode because as all the power supplies are at half-voltage, the amplifier will still operate at half power when the Ever-Warm mode is engaged, so the user should use the MUTE switch when in this mode.
The front-panel mute switch and angled-back chassis make it easier to hook up the interconnects, speaker cables, and IEC power cord.
In our own in-house magnetics department, our R&D team completely redesigned all of our output transformers in 1998 with the goal to reclaim that luscious rich mid-range of our vintage designs. In 2013 we reworked the output transformer to operate the output stage in Ultra-Linear mode which is a great sounding balance between the detail of triode and the brawn of Tetrode. We also specifically set out to achieve a deeper bottom register at higher power with lower distortion. Hours and hours of listening tests, measurements, and fine-tuning brought an exciting and stunning result to our ears. We hope you will agree.
- Chúng tôi luôn hướng đến sự hài lòng của khách hàng một cách tốt nhất.
- Giao hàng và bảo hành nhanh chóng trong vòng 24h.
- Dịch vụ hậu mãi, nhân viên chu đáo.
- Linh kiện, phụ kiện thay thế cam kết chính hãng, lắp đặt đúng quy trình của nhà sản xuất.
Thông số kỹ thuật cơ bản của Power Amplifier Manley Neo-Classic 250 Monoblock
-
ALL-TUBE monoblock design: uses 10 x Tungsol EL34B output tubes
-
Driver Stage: High current double 12BH7EH (x2)
-
Input Tube: 12AT7
-
BALANCED & UNBALANCED inputs: RCA and XLR jacks (switchable)
-
MUTE switch: on front panel
-
TRIODE / Ultra-Linear output mode switching: on front panel
-
SOFT-START turn on mode: minimizes in-rush current by first powering up amplifier to half voltages
-
EVER-WARM mode: for standby keeps tubes warmed up at half voltages
-
MANLEY IRON® Output Transformer: designed and wound at Manley Labs
-
Front panel bias measurement and adjust: Concealed under the black oval insert
-
Output Tube Standing Current: 30mA
-
Set Bias for: 300mVDC measured across each bias tip jack to ground
-
Large filter / reservoir capacitors: 3800uF x 2
-
Angled rear of chassis: provides for easy connections
-
WBT binding posts: CE compliant for European models
-
Input Sensitivity RCA: Triode = 1.17 V; UL = 1.38 V for full power into 5 Ohms
-
Input Sensitivity XLR: Triode = 2.56 V; Tetrode = 3.05 V for full power into 5 Ohms
-
Input Sensitivity RCA Triode: 98.3 mV; UL = 86.6 mV for 1 Watt into 5 Ohms
-
Input Sensitivity XLR Triode: 227 mV; UL = 200 mV for 1 Watt into 5 Ohms
-
Gain RCA: Triode = 27.2 dB; UL = 28.3 dB
-
Gain XLR: Triode = 21.2 dB; UL = 22.3 dB
-
Input Impedance RCA: 130 kOhm @ 1KHz
-
Input Impedance XLR: 278 kOhm @ 1KHz; 20 kOhms @ 20KHz; 28 kOhm @ 20Hz
-
Actual Output Impedance Triode: 0.610 Ohm
-
Actual Output Impedance Tetrode: 0.698 Ohm
-
Optimum Speaker Load: 5 Ohms
-
Damping Factor Triode: 13.1
-
Damping Factor Tetrode: 11.5
-
S/N Ratio: 94 dB A-WGT at 1 Watt into 5 Ohms
-
Dynamic Range: 114 dB A-WGT
-
Noise Floor: -84 dB or 50 µV A-WGT 1 Watt into 5 Ohms w/Shorted Input
-
Frequency response -1 dB: Triode = 10 Hz - 30 kHz
-
Full Power frequency response -1 dB: Triode = 10 Hz - 33 kHz; UL = 10 Hz - 20 kHz to reach 1.5% THD into 5 Ohms
-
Distortion: Triode = 0.052%; UL = 0.37% BW 10 Hz - 500 kHz at 1 Watt into 5 Ohms
-
Full Power Triode: 140 W @ 1.5% THD into 5 Ohms
-
Full Power UL: 250 W @ 1.5% THD into 5 Ohms
-
Power Consumption: 40 Watts in "EVER-WARM" mode
-
Power Consumption Idle: 335 Watts
-
Maximum Power Consumption: 710 Watts at full power
-
Operating Mains Voltage: Factory set for 100V, 120V or 220-240VAC operation for original destination country's mains voltage.
-
Operating Mains Voltage: changeable with power transformer replacement and fuse value change.
-
Mains Voltage Frequency: 50 Hz or 60 Hz
-
Mains Fuse 100-120VAC operation: MDA 10 Amp SLO-BLO Ceramic Time-Delay fuse
-
Mains Fuse 220-240VAC operation: MDA 8 Amp SLO-BLO Ceramic Time-Delay fuse
-
B+ Fuse: MDA 1 1/2A SLO-BLO Ceramic Time-Delay fuse
-
Badge Illumination: Units produced before 4/2003 use 8V, 0.3A "Fuse-Lamp" 1/4" X 1 1/4"
- Serial numbers after N250188 use LED illumination which probably won't burn out
-
Power Cord: Detachable IEC standard. Appropriate power cord supplied for destination country
-
Unit Dimensions: W=19" x D=13" x H=9" each
-
Unit Weight: 69 lbs. each
-
Shipping Box Dimensions: 22” x 19” x 18”
-
Shipping Weight: 79 lbs. each
Prior Production Models with Triode-Tetrode Switching
-
Input Sensitivity RCA: Triode = 1.637 V, Tetrode = 1.837 V for full power
-
Input Sensitivity XLR: Triode = 3.2 V, Tetrode = 3.6 V for full power
-
Input Sensitivity Triode: 174 mV for 1 Watt into 8 Ohms
-
Input Sensitivity Tetrode: 146 mV for 1 Watt into 8 Ohms
-
Gain Triode: 30 dB
-
Gain Tetrode: 32 dB
-
Input Impedance RCA: 116 kOhm @ 1KHz
-
Input Impedance XLR: 270 kOhm @ 1KHz; 20 kOhms @ 20 kHz; 38 kOhm @ 20Hz
-
Actual Output Impedance Triode: 0.538 Ohm
-
Actual Output Impedance Tetrode: 0.465 Ohm
-
Damping Factor Triode: 14.8
-
Damping Factor Tetrode: 17.2
-
Full Power Tetrode: 250W @ 1.5% THD into 5 Ohms
-
Full Power Triode: 100W @ 1.5% THD into 5 Ohms